TableGauge

Single or dual axis systems

Using the Xactum Intelligent Laser Gauges as bench-top micrometers in the Table-Gauge configuration, with no other instruments you can measure diameters quickly, accurately and easily.

It's the ideal instrument to check pins, ground or other turned parts.

No matter what the operators skill level, it is possible to achieve ultra-accurate and perfectly reproducible measurements thanks to outstanding Laser Technology.

The XLS gauges are programmed with dedicated software and are completed with a display unit, a remote control, fixings to hold the part and a base-plate for bench-top use.  Using this “Table-Gauge” assembly you can, in a few seconds, check the diameter, roundness and the concentricity of ground or turned parts, to an accuracy previously only obtained in a metrology room using much more expensive equipment and specialised personnel.

Contact Our Sales Team

Contact our sales team via email regarding this product

Email Us
Send an Enquiry

Use our contact page to send us a message or enquiry

Make an enquiry
Dual Axis
Extruline XY13/A XY13/B XY35/B
Gauge Model XLS13XY/1500/A XLS13XY/1500/B XLS35XY/1500/B
Measuring field (mm) 13 x 13 4 x 4 35 x 35
Measurable Diameters (mm) 0.1 - 10 0.05 - 3 0.2 - 32
Resolution (selectable) 10/1/0.1/0.01
Linearity (centred) (µm) ±0.5
Linearity (Reduced Field) (µm) ±1 ±0.5 ±1.5
Repeatability (T=1s, ±2σ) (µm) ±0.04 ±0.02 ±0.15
Beam Spot Size (mm) 0.1 x 4 0.05 x 0.1 0.2 x 0.1
Scanning Frequency (Hz) 1500(X) x 1500
Single Axis
Extruline X40/A X80/A
Gauge Model XLS/40/1500/A XLS80/1500/A
Measuring field (mm) 40 80
Measurable Diameters (mm) 0.1-38 0.75-78
Resolution (selectable) 10/1/0.1/0.01
Linearity (centred) (µm) ±0.5 ±1
Linearity (Reduced Field) (µm) ±0.5 ±2
Repeatability (T=1s, ±2σ) (µm) ±0.07 ±0.2
Beam Spot Size (mm) 0.08 x 2 0.4 x 3.5
Scanning Frequency (Hz) 1500 1500
  • Multicolor LED display to show the measured values and to allow system programming through the IR remote control
  • The measured and programmed data can be scrolled on the display using the remote control or the SET key on the display panel
  • It is possible to save in memory, in a Product Library, up to 1000 different sets of programmed parameters, for each specific part to be checked
  • The display colour will change corresponding to the tolerance status of the shown variable (green, orange or red)
  • The display unit includes 4 programmable alarm output lines to drive additional external devices
  • Simple and quick programming using the remote control keys and the messages on the display
  • Offset function for user re-mastering
  • Selectable Measuring Units inch/mm and Resolution (to 0.01μm / 1x10-6 inch)

     
  • Wire samples
  • Fibre optics
  • Magnet wire
  • Ground parts
  • Bearings
  • Hydraulic components
     
  • V blocks to hold the part
  • Linear slide and the gauge-base to translate the part
  • Fixed V blocks to be mounted on the slide
  • Centers and cones to hold the part
  • Foot switch
  • Hand-held programming terminal
  • GageXcom software for PC communication.
  • Hand driven rotating fixture (for the XLS13XY only)

     
For further information or enquiries Give us a call or fill in our online enquiry form
+44 (0)1823 333343